Simple Mode: A Classic Spot Meter on Your Phone
Version 1.5 rebuilds the Simple theme the way hand-held spot meters have always worked: a circle, a dial, and a button that holds the reading.
A meter with one job
A Pentax Spotmeter V has a trigger, a one degree circle and a dial. You aim, you read a number, you turn the dial until that number sits on the index, and every shutter speed on the ring is now standing next to the aperture that goes with it. No menus. No film database. Photographers carried that meter for forty years because it only did one thing.
Simple, the third theme in Zone Light Meter, has been rebuilt around the same idea for version 1.5. It arrived a few days earlier as a quick answer to a comment in a film group, asking for a screen where you set the ISO and the shutter and the phone tells you the aperture for whatever you point at. It worked. It was also a bit of a puzzle: the aperture came with a small +1/3 or -1/3 next to it, there was no way to choose the aperture and read the time instead, and the numbers stopped at the limits of whichever lens was selected in the main app. A hand-held meter has no idea which lens is in your bag.
What is on the screen now
The viewfinder is clean: a circle in the middle and a LIVE badge. Under the picture sits a black display with three values, EV, shutter and aperture. The white one is yours. The big orange one is the meter's answer. That colour rule holds everywhere on the screen, which is most of what makes it readable at arm's length.
Below the display, a film speed button and a switch labelled YOU SET. On Shutter you pick the time and the meter gives the aperture, which is what you want when 1/500 has to stop a cyclist. On Aperture you pick the f-number and the meter gives the time, for f/2 on a portrait or f/16 on a tripod. Flip the switch and the pair on screen stays put. Only the roles trade places.
The dial, laid out flat
Then comes the part borrowed straight from the old meters. Two rows of numbers slide under a fixed mark: shutter speeds on top, apertures below, each speed standing over its aperture for the light in the circle. If the mark shows 1/125 over f/8, the same glance shows 1/250 over f/5.6 and 1/60 over f/11. Same exposure, traded between motion and depth of field. Drag the scale to set your value, or tap a number to bring it to the mark.
Whole stops are printed and the two ticks between them are thirds, so a reading that falls between f/5.6 and f/8 is something you can see, the way you would on an engraved dial. That replaces the old +1/3 marks. And if f/6.3 and f/9 mean nothing to the lens in your hand, a second switch, STOPS, makes the whole meter work in whole stops: f/5.6, f/8, f/11, and nothing in between.
Hold, and the edges of the scale
Tap the picture, press HOLD or press a volume key and the reading freezes, picture included, so you can lower the phone and set the camera without the number wandering off. Change the film speed or your own value while it is held and the answer follows, as it would on a real dial.
When no value fits, the answer rests on the end of its scale in red and a line says why: Too dark for 1/1000, with a Try button that offers the nearest speed that works. A spot the phone's sensor cannot read exactly, a bare bulb or a deep shadow, also shows red, with a note that the true value is at most or at least what is shown. Holding such a spot takes a slower, more careful reading.
What Simple leaves out, on purpose
Simple does not read the camera, lens or film you picked in the rest of the app. Its scales are its own: ISO 0.8 to 12800, 34 minutes to 1/8000, f/1 to f/360, in thirds of a stop. Only your meter calibration carries over. Filters, exposure compensation, zone placement, bellows and reciprocity stay in Classic and Paper, and nothing metered in Simple goes into the shot log. The app says so in a short warning the moment you choose the theme, because a meter that quietly ignores your red filter is worse than one that tells you.
That trade is the whole point. Pinch to tighten the circle, about three degrees by default. Calibrate once against a meter you trust. Then it is a circle, a dial and a HOLD button, which is all a spot meter ever was. The full reference is in the Simple theme documentation, and Simple lives under Settings, Theme, on Android and iPhone.
This article was drafted with AI from researched sources and checked against manuals and maker data. Nobody here has hands-on tested every item. How the articles are made. Spotted a mistake? Write to hello@zonelightmeter.com.